PDA

View Full Version : X400 General Discussion

Pages : 1 [2]
  1. Glitchs after a crash.
  2. My x-400 decided it was time for a crash
  3. MaxAmps 1500 not even coming close
  4. X400 Blade grips on the Trex full aluminum head
  5. CAD work in progress
  6. I'm feeling it !!!
  7. Tail Slide
  8. x-400 stock pinion bore size
  9. CHEAP PLASTIC w/MX400 Pro
  10. Newbie need some help
  11. ELE Brushless ESC programming problem!
  12. MX400 Pro Kit
  13. Tail vibration fix?
  14. GY401/240 voltage
  15. Carbon Fiber main blade suggestions???
  16. cut out
  17. Custom control rods
  18. Another one bites the dust!
  19. Servo lead, be careful!
  20. My luck is changing, for the worse !
  21. Converting the x-400 to a Trex frame.
  22. In summation....
  23. cc35 fears
  24. New Aluminum Center Hub with BB
  25. New hub bearings?
  26. 315mm blades on X-400
  27. How can I tell if my gyro is shot?
  28. Chattering problem
  29. Not enough way for Nick + Roll
  30. Is the Trex main shaft compatable?????
  31. Tail Bounce
  32. How to fit trex blade holders to X400
  33. anyone tried this motor?
  34. Yet another one bites the dust, same problem! Need advice
  35. Bling Head for X400
  36. Video camera in the X-400
  37. Tedani skid adaptors
  38. Futaba Digital Servo Question
  39. Center Hub/head block let go
  40. Tail Pitch Plate & Tail Pitch Lever
  41. Starting 3D - Equipment Upgrade Recommendations
  42. Tail assy is turning
  43. Tail Pitch Plate and Tail Pitch Lever
  44. Now I got the tail wag damn it
  45. Align Blades On Stock Ark Grips
  46. Main Blade Tracking problem?????
  47. HELP WITH THE SIM DEMO & DOWNLOADS
  48. Governor mode setup
  49. X400 at RC-Expert Store
  50. Bluebird 371 Worth Using?
  51. ESC MX400Pro problems
  52. tail rotor pitch creep
  53. CF flybar paddles
  54. Mixing arms
  55. mx400 with 400l
  56. mixing 3 and 4 cell power?
  57. Issues after upgrade???
  58. Flybar length
  59. Telebee Gyro setup with FF9 super
  60. telebee gyro
  61. What revs with plastic blade holders?
  62. Is my tail servo too slow
  63. Some final thoughts
  64. CF tail booms
  65. livening up the x400
  66. alternative spares (Trex)
  67. max head speed for mx-400
  68. Recommended Lipo balance chargers?
  69. Decoding the RC-Expert ESC-BS40A beeps
  70. Fitting the bodyshell on the X400 around the battery shelf
  71. Futaba transmitter battery upgrade
  72. Charging a NiMH Tx battery
  73. Flying with no Gyro
  74. Alluminium skip mount adaptors
  75. Help With Setting Up Tail
  76. Recommended servos for x400
  77. Ally suppliers for the x400
  78. Need advice on new ESC and motor for X400 please!
  79. X400 CCPM conversion linkage length
  80. X400 Glitching after few minutes of hover
  81. Always put the canopy on!
  82. mods so far...
  83. Yippy! - Cabin Painted, pictures included
  84. wobblers
  85. High Voltage
  86. Motor choice on X400
  87. X-400 extended tail boom ???
  88. Turnbuckle
  89. Ark 500
  90. Mx400, rotor head seperated in flight
  91. Uncontrollable Tail Wag (Telebee Gyro)
  92. mx400 pro tail case bearings
  93. Tail Drift
  94. Heli-Max MX400 Pro Questions
  95. Ark 400
  96. WARNING X400 Tail hub
  97. zoom 400 and x400 tail control rod = the same?
  98. is there alternative x400/mx400 main gear?
  99. 3 minutes flight time
  100. final adjustments and radio set up
  101. Ark 450
  102. Elec heli Tachometer
  103. Motor efficiency
  104. Where to buy X400 kits
  105. Ark x-400 main gear